risk-management – web-dev-net-platform – কুইজ মডেল টেস্ট অনুশীলন – 33

12638. What will cause a router to enter setup mode?

1. The configuration register is set to 0x2100.
2. Boot system commands are misconfigured in the running-configuration.
3. None of the above
4. The configuration file is missing in NVRAM.

12639. You are a trainee technician at a company. Your instructor tells you to backup an IOS image of a Cisco device to a Windows 2003 server on the network. What should you do first?

1. Assure that the network can transfer authenticated data.
2. Check that the authentication for access is set.
3. None of the above
4. Make sure that the network server can be accessed

12640. Which command on router A will assign the last usable IP address from the 192.168.32.128/28 subnetwork to a router interface?

1. A(config-if)# ip address 192.168.32.145 255.255.255.240
2. A(config-if)# ip address 192.168.32.142 255.255.255.240
3. A(config-if)# ip address 192.168.32.158 255.255.255.240
4. A(config-if)# ip address 192.168.32.143 255.255.255.240

12641. A network administrator needs to configure a serial link between the main office and a remote location. The router at the remote office is a non-Cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?

1. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.255 Main(config-f)# encapsulation ietf
2. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.255 Main(config-f)# encapsulation ppp Main(config-if)# no shut
3. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.255 Main(config-f)# no shut
4. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.255 Main(config-f)# encapsulation frame-relay Main(config-if)# authentication chap Main(config-if)# no shut

12642. You need to upgrade the IOS of an existing router on your network. The new IOS image is located on a TFTP server that you have set up within the network. What command should you issue in order to download the new IOS version?

1. Router(config)# repair flash
2. Router(config)# restore flash
3. Router# copy tftp flash
4. Router# copy flash run

12643. What is the default configuration register setting on most Cisco routers?

1. 0x2012
2. 0x2210
3. 0x2104
4. 0x2102

12644. If an ethernet port on router PC1 was assigned an IP address of 172.16.112.1/20, what is the maximum number of hosts allowed on this LAN subnet?

1. 4094
2. 2046
3. 1024
4. 4096

12645. Before installing a new, upgraded version of the IOS, what should be checked on the router, and which command should be used to gather this information?

1. the version of the bootstrap software present on the router
2. show running-config
3. the amount of available ROM
4. show version

12646. You need to configure a default route on a router. Which command will configure a default route on a router?

1. PC1 (config)# ip default-gateway 10.1.1.0
2. PC1 (config)# ip default-route 10.1.1.0
3. PC1 (config)# ip route 0.0.0.0 10.1.1.0 10.1.1.1
4. PC1 (config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1

12647. During startup, router PC1 displays the following error message: boot: cannot open “flash:” What will PC1 do next?

1. It will attempt to locate the configuration file from a TFTP server If this fails
2. it will load a limited configuration from ROM It will attempt to locate the IOS from a TFTP server
3. If this fails it will load a limited IOS from ROM It will attempt to locate the configuration file from a TFTP server
4. If this fails it will initiate the setup dialog.Because of damaged flash memory

আমাদের কাছে থাকা লক্ষ লক্ষ মডেল টেস্ট থেকে প্রাকটিজের জন্য কিছু এখানে তুলে ধরা হল। প্রতিটি অধ্যায়ের উপরে ইশিখন.কম কুইজ চ্যালেঞ্জ এ আছে শত শত মডেল টেস্ট বার বার মডেল টেস্ট দিয়ে নিজেকে যাচাই কর এবং পুরো বাংলাদেশের সকল শিক্ষার্থীর সাথে আপনার মেধা তালিকা দেখুন। প্রশ্নে কোন প্রকার ভুল থাকলে সঠিক উত্তরসহ নিচে কমেন্ট করে জানাবেন, আমরা ঠিক করে দেবো।